The settings shown above are the preferred settings, not the defaults. When creating the
array for the first time, make sure to select “Security” as the first choice. “Typical Application”
setting has not been defined. Verify that the Array Mode as shown in the middle section shows
“Mirror/Stripe.” Press CTRL-Y per the menu on the bottom once the settings are correct to see
the following message:
FastBuild (tm) Utility 1.32 (c) 1996-2001 Promise Technology, Inc.
╔══════════════════════════[ Auto Setup Options Menu ]═════════════════════════╗
║ Optimize array for : Security ║
║ ║
║ Typical Application to use: DESKTOP ║
╚══════════════════════════════════════════════════════════════════════════════╝
╔═════════════════════════[ Auto Setup Configuration ]═════════════════════════╗
║ ║
║ ║
║ Mode .......................................... Mirror/Stripe ║
║ ╔═════════════════════════════════╗ ║
║ Spare Drive ......║ Array has been created.... ║ ║
║ ║ <Press Any Key to REBOOT> ║ ║
║ Drive(s) Used in A╚═════════════════════════════════╝ ║
║ ║
║ Array Disk Capacity (size in MB)............... ###### ║
║ ║
║ ║
║ ║
║ ║
╚══════════════════════════════════════════════════════════════════════════════╝
╔═══════════════════════════════[ Keys Available ]═════════════════════════════╗
║ ║
║ [▲] Up [▼] Down [◄,►,Space] Change Option [ESC] Exit [CTRL-Y] Save ║
╚══════════════════════════════════════════════════════════════════════════════╝
3. Once the array is created, press a key to reboot, then the Promise controller’s banner
should be as shown below; however, this time only a brief pause for the Ctrl-F hotkey
will take place instead of waiting for a selection.
HcuvVtcm!VZ3111!)vo*!CKQU!Xgtukqp!3/11/1/44!
)e*!2:6.3113!Rtqokug!Vgejpqnqi{-!Kpe/!Bnn!tkijvu!tgugtxgf/!
!
!
KF!!!!!OQFG!!!!!!!!!!!!!!!!!!!!UK\G!!!!!!!!!!VTBEM.OBRRKPI!!!!!!!!!!UVBVWU!
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>!
2!+!!!!3z3!Okttqt0Uvtkrg!!!!!!!zzzzzzzO!!!!!!zzz0zzz0zzz!!!!!!!!!!!!HWPEVKQPBN!
!
Rtguu!=Evtn.H?!vq!gpvgt!HcuvCwknf!)vo*!Wvknkv{!
The details shown under SIZE will describe an array approximately 120-160GB in size.
4. Once the above steps are completed, allow Windows 2000 to boot up, log on to it, then
format the array using these steps:
a. Right-click on the “My Computer” icon and select “Manage” from the context
menu.
b. In Computer Management’s left pane, select Disk Management.
c. Windows should walk through a short “Write Signature” wizard. It should also
indicate only one volume to select (which needs to be selected)
d. Right-click on the GRAY SQUARE representing the drive (array). Select “Revert
to Basic.” The gray square should change from “Dynamic” to “Basic.”
e. Right-click on the Unallocated Space next to the gray square, and select “Create
Partition.” Entire disk, NTFS format, ALLOCATION UNIT SIZE 64K.
(58 stránky)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce