Promise Technology E610s Manuál Strana 202
- Strana / 434
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
VTrak E-Class Product Manual
184
To view enclosure topology:
1. From the Main Menu, highlight Subsystem Management and press Enter.
2. Highlight Enclosure Topology and press Enter.
The following information applies to the Head Unit:
• Enclosure number – 1
• Controller number – 1 or 2
•Port number
• Status – OK is normal. N/C is not connected
•Link Width
The following information applies to RAID cascaded units or JBOD
expansion units:
• Connected EnclWWN – The subsystem identified by its World Wide
Number (WWN)
• Connected(Encl,Ctrl,Port) – The subsystem’s enclosure, controller,
and port numbers where the data connection was made
If there is no connection, the value shows N/A.
- E610f, E610s, E310f, E310s 1
- Copyright 2
- Trademarks 2
- Recommendations 2
- VTrak E-Class Product Manual 10
- Contents 11
- About This Manual 19
- VTrak Overview 20
- Architectural Description 22
- Features and Benefits 23
- Operational Features 24
- Management 25
- Specifications 26
- Warranty and Support 27
- BSMI Statement 27
- CE Statement 27
- FCC Statement 27
- GOST-R Statement 28
- IRAM Statement 28
- KCC Statement 28
- Chapter 2: VTrak Installation 29
- Mounting VTrak in a Rack 30
- Installing Disk Drives 33
- AAMUX Adapter 34
- WARNING: 35
- Counter-sink screws only 35
- Fibre Channel SAN 37
- Fibre Channel DAS 39
- FC 1 FC 2 41
- Expansion 42
- Data Path 45
- Management Path 45
- SAS Cascaded Storage 47
- SAS with JBOD Expansion 50
- Connecting the Power 55
- Chapter 3: VTrak Setup 57
- VTrak Default IP Addresses 58
- Setting up VTrak with the CLI 59
- Setting up VTrak with the CLU 61
- Manual IP settings 62
- Automatic IP settings 62
- Setting Up WebPAM PROe 64
- Choosing a Language 65
- Creating a Disk Array 66
- Automatic 67
- Advanced 68
- Logging out of WebPAM PROe 70
- Logging into WebPAM PROe 72
- Perusing the Interface 75
- Using the Header 76
- Using Tree View 76
- Using Management View 77
- Viewing the Event Frame 78
- Viewing Other Subsytems 80
- Logging into a Subsystem 80
- Hiding the Other Subsystems 80
- Working with Subsystems 81
- Viewing Subsystem Information 82
- Viewing the Runtime Event Log 84
- Saving the Runtime Event Log 85
- Viewing NVRAM Events 86
- Saving NVRAM Events 87
- Running Background Activities 89
- Viewing Scheduled Activities 90
- Scheduling an Activity 90
- Deleting a Scheduled Activity 91
- Viewing Lock Status 91
- Setting the Lock 92
- Renewing the Lock 92
- Releasing the Lock 92
- Setting-up Event Notification 95
- Viewing User Sessions 98
- Logging out Other Users 99
- Port Setting Information 103
- Property Definitions 104
- Viewing SFP Information 105
- Adding an Initiator 107
- Managing SAS Connections 108
- Viewing SAS Port Statistics 109
- Viewing SAS Initiators 109
- Managing Storage Services 111
- Deleting an Initiator 112
- Viewing the LUN Map 112
- Enabling LUN Masking 112
- Adding a LUN Map 112
- Editing a LUN Map 113
- Monitoring Performance 114
- Managing Software Services 116
- Making SLP Settings 117
- Making Web Server Settings 118
- Making Telnet Settings 119
- Making SSH Settings 120
- Making SNMP Settings 120
- Managing SNMP Trap Sinks 121
- Making CIM Settings 122
- Making Netsend Settings 123
- Managing Netsend Recipients 124
- Deleting Netsend Recipients 125
- Exporting the User Database 126
- Importing a User Database 128
- Updating the Firmware 130
- Restoring Factory Defaults 132
- Clearing Statistics 133
- Shutting Down the Subsystem 135
- Starting Up After Shutdown 136
- Restarting the Subsystem 137
- Managing Controllers 138
- Adjustable items 139
- Viewing Controller Statistics 140
- Making Controller Settings 140
- Clearing an Orphan Watermark 142
- Managing Enclosures 143
- Viewing Enclosure Topology 144
- Viewing Enclosure Information 144
- Making Enclosure Settings 145
- Viewing FRU VPD Information 145
- Checking the Batteries 146
- Reconditioning a Battery 146
- Silencing the Buzzer 147
- Making Buzzer Settings 147
- Testing the Buzzer 148
- Managing Physical Drives 149
- Adjustable Items 151
- Managing UPS Units 154
- Making UPS Settings 155
- Viewing UPS Information 156
- Managing Disk Arrays 157
- Deleting a Disk Array 162
- Making Disk Array Settings 163
- Creating a Logical Drive 163
- Deleting a Logical Drive 165
- Migrating a Disk Array 165
- Rebuilding a Disk Array 166
- Rebuilding Manually 167
- Running PDM on a Disk Array 168
- Transitioning a Disk Array 168
- Managing Logical Drives 170
- Making Logical Drive Settings 172
- Initializing a Logical Drive 173
- Running Redundancy Check 173
- Table Definitions 175
- LUN Mapping Parameters 176
- Managing Spare Drives 177
- Creating a Spare Drive 178
- Deleting Spare Drive 179
- Making Spare Drive Settings 179
- Running Spare Check 180
- Initial Connection 184
- Making a Telnet Connection 185
- Making a SSH Connection 185
- Logging In 186
- Accessing Online Help 187
- Exiting the CLU 187
- Logging Out of the CLI 188
- Running Quick Setup 189
- Managing the Subsystem 190
- Running Media Patrol 191
- Making NTP Settings 192
- Managing the Controllers 194
- Locating the Controller 196
- Managing the Enclosure 197
- Viewing Power Supply Status 198
- Locating a Power Supply 199
- Viewing Cooling Unit Status 199
- Viewing Voltage Sensor Status 200
- Locating an Enclosure 201
- Setting an Alias 204
- Locating a Physical Drive 206
- Disk Array Operational Status 212
- Accepting an Incomplete Array 213
- Running PDM 215
- Locating a Disk Array 216
- Deleting a Spare Drive 221
- Locating a Logical Drive 225
- Making Automatic Settings 226
- Making Manual Settings 226
- Viewing Node Information 228
- Adding a SAS Initiator 233
- Managing Background Activity 234
- Working with the Event Viewer 236
- Clearing NVRAM Events 237
- Working with LUN Mapping 238
- Mapping a LUN to an Initiator 239
- Managing Users 243
- Changing Your Own Password 245
- Deleting a User 246
- Making Email Settings 247
- Making Webserver Settings 248
- Flashing through TFTP 255
- Chapter 6: Maintenance 267
- Replacing a Power Supply 277
- Replacing a Cache Battery 283
- Removing the old controller 287
- Installing the new controller 287
- Introduction to RAID 291
- RAID 0 – Stripe 292
- RAID 1 – Mirror 293
- RAID 1E – Enhanced Mirror 294
- RAID 10 – Mirror + Stripe 297
- RAID 50 Axles 299
- RAID 60 Axles 301
- Choosing a RAID Level 302
- Choosing Stripe Size 305
- Choosing Sector Size 305
- Cache Policy 306
- Read Cache Policy 307
- Write Cache Policy 307
- Adaptive Writeback Cache 307
- Cache Mirroring 308
- LUN Affinity 309
- Logical Drive Settings 310
- Failover and Failback 310
- Capacity Coercion 311
- Initialization 311
- Hot Spare Drive(s) 312
- RAID Level Migration 312
- Figure 1 318
- PDM Triggers 320
- Transition 321
- Automatic Transition 323
- Manual Transition 323
- Chapter 8: Troubleshooting 325
- LEDs Display Amber or Red 327
- Drive Status Indicators 328
- Back of Enclosure 328
- CLU Reports a Problem 333
- Checking a Reported Component 334
- WebPAM PROe Reports a Problem 336
- Figure 13.The Event Log 337
- Event Notification Response 339
- When a Physical Drive Fails 354
- With a Hot Spare Drive 354
- Without a Hot Spare Drive 355
- Rebuild Operation 355
- Incomplete Array 357
- Physical Drive Problems 358
- Enclosure Problems 360
- Serial Connection 364
- Telnet Connection 365
- Connection Problems 366
- Fibre Channel Connections 367
- SAS Connections 368
- Chapter 9: Support 371
- Contacting Technical Support 373
- The Netherlands 374
- Attn: Technical Support 375
- Limited Warranty 376
- Your Responsibilities 377
- SNMP MIB Files 381
- Adding a Second Controller 381
- Before You Begin 385
- Installing PerfectPath 386
- Verifying Installation 387
- Running Perfect Path View 389
- Viewing LUN Properties 390
- Viewing Path Properties 392
- Clearing Path Statistics 394
- Features and Settings 395
- Load Balance Policy 396
- Path Verification 397
- PDO Removal 398
- Performance Tab Refresh Rate 399
- Round Robin Count 399
- Refreshing the Objects 400
- Viewing System Information 400
- Saving System Information 401
- Troubleshooting 402
- Updating PerfectPath 403
- Repairing PerfectPath 404
- Removing PerfectPath 405
- Installing Packages 409
- Verifying Packages – RedHat 409
- Verifying Packages – SuSE 410
- RedHat Systems 412
- SuSE Systems 412
- Editing a Configuration File 412
- 10 SP3, and 11 414
- (or a similar message) 419
- Sample multipath.conf File 420
Související produkty a manuály pro Řadiče RAID Promise Technology E610s
(2 stránky)
(4 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce